Add routing in windows xp

Make sure that you select the right one, especially if you haven't backed up your registry recently. Method 3. Search the service "Routing and Remote Access" , it will be disable by default. To enable it right click on it and then select properties and change the "Startup Type" to "Manual" if you want to start it when you require or "Automatic" to start it whenever computer boots on else "Automatic delayed" if you want it to initiate a little bit later after the other services in your computer are started at boot time.

Now right click the Routing and Remote access service and press start and let the progress bar complete. This means Routing has been enabled.

Start it up again with the above notes to help you, If this does not help run a reg cleaner, the try again. Yes No. Not Helpful 1 Helpful 1. I did the Routing and Remote Access part, but when I did Start it loaded for a little chunk and then stopped and a Service box popped up and said the Routing started and stopped.

Any help here? Try to refresh or just mess around with stuff and find out what to do if it happens again. Not Helpful 5 Helpful 0. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Before you make any changes, make sure that you back up your registry.

This will protect your system if you make a mistake while changing registry values. If you skip this step, you might end up damaging your entire system. Using an invalid combination of a destination and subnet mask netmask value displays a "Route: bad gateway address netmask" error message. This error message appears when the destination contains one or more bits set to 1 in bit locations where the corresponding subnet mask bit is set to 0.

To test this condition, express the destination and subnet mask using binary notation. The subnet mask in binary notation consists of a series of 1 bits, representing the network address portion of the destination, and a series of 0 bits, representing the host address portion of the destination. Check to determine whether there are bits in the destination that are set to 1 for the portion of the destination that is the host address as defined by the subnet mask.

This parameter is not supported by the route command for Windows 95 or Windows To add a route to the destination To add a persistent route to the destination To change the next hop address of the route with the destination of Skip to main content. A routing table dictates where all packets go when they leave a system—whether that system is a physical router or a PC. Most routers—including the one built into your Windows PC—use some form of dynamic routing, where the router is capable of selecting the best place to forward packets based on information it gets from other routers.

If any of those apply to you, read on. Before you get started adding routes, it may be helpful to view the routing table first. You can do pretty much everything in PowerShell that you can do in Command Prompt, plus a lot of other useful things. The metric cost value is just a cost that is relative to other costs in the table and is used when Windows decides between multiple routes that could reach the same destination.

So, for example, if you wanted to add a route specifying that all traffic bound for the When you add a static route, by default it only lasts until the next time you start Windows. The reason for this is that many companies use a coordinated list of static routes that gets updated fairly often.

Rather than adding and updating all those routes on every machine, they just distribute a batch script file that adds the newest routes during Windows startup. This keeps the routing table relatively uncluttered.

You could certainly use the batch script method yourself. A persistent route stays in place even when Windows starts up. Using the same command we used earlier, you could make that route persistent with the following modification:. Of course, there will come a time you might want to remove a static route from your table. All you have to do is type a command using the following syntax:.

So, to delete the route we created earlier with the destination network Yes, using static routes is a bit esoteric when it comes to managing most home and small business networks.

The members, admins, and authors of this website respect your privacy. All logos and trademarks in this site are property of their respective owner. Quinn was one of the original co-founders of Tech-Recipes.

View more articles by Quinn McHenry. The Conversation Follow the reactions below and share your own thoughts. Leave a Reply Click here to cancel reply.