Bewator entro installation manual

The mechanical parts for this function have to be ordered separately and mounted to get this tamper work. K Extra relay outputs, switches parallel with each relay output. Can be used for controlling a light panel etc. Flashes quickly when communication is working properly, slowly when interrupted autonomous mode. M Choose the address for or N Set the relay central address by placing the link on the required number.

E Remote opening input. F Door monitor input for door contact. Configured by the installer program. G Opening relay. H Power supply for electric locking device. Max mA. I Tamper switch. No connection on reader terminal 5 and 6 is then allowed. Two links are used. D Tamper switch. E Connect the screen in case of long distances or disturbing environment. C Tamper switch. D Buzzer. Connecting the BC18 remote card reader Fig. Entro range of proximity readers and Hands-Free readers.

The following examples show shorthand information for some typical readers. You may have it always lit when the door is locked. See page 45 for using these readers in Anti-pass back applications. XH Fig. However - the reading distance permits both entry end exit functions in the same reader. Remember to set the jumper J3 on Entro see item N and address it in the range The mechanical design is exactly as the DC12 see page See the table below for the electrical installation and setup. Maximum load 2 A.

Software controlled. When Alert is selected also the tamper switch will activate this relay. I Input for door monitor contact. Maximum load mA. Default: Stand-Alone.

O Jumper for address selection for Entro Lite or Entro. Default: Address 1 P Tamper switch. Will also activate the relay in item G when this is setup as Alert. Wiring the door monitor contact and lock are done as usual. EXIT reader 2.

Electric lock 45 Bewator AB ENTRY 2. EXIT 3. Power supply 4. Opening relay 5. Lock 6. Remote opening 7. Door contact 8. Opening relay. Voltage free contacts 9. This means that the first door has to be closed before the next door can be unlocked. To be able to monitor the status of the doors, both must be equipped with door monitor contacts.

We strongly recommend that also some suitable mechanical, emergency opening equipment is mounted in the interlock zone from within the interlock zone. Door monitor contacts. Electric Lock. The distance to the PC depends on the cable configuration of the network itself hubs, switches etc. You must confirm with the IT Manager the correct IPaddresses and installation settings for the system.

In this case you use a network cable between the PC and the network switch in the SR34i. Preferably in the range The illustration below shows an available, complete kit consisting of a wall socket IF1 , a standard RS cable approx. You can use the standard cable directly alt.

RS needs fewer settings in the PC, which simplifies the set-up. You can also temporally use RS — and then change to Ethernet later. The total distance between PC or printer and the segment controller must not exceed 25 meters maximum. Note that either a PC or a printer can be connected to a segment controller — not both.

It can be used for: z Login of cards z Login to system software with card. It is supported of a software driver USB-Agent installed along with the Entro software is loaded when booting the computer. Apply power when you start the system see the Check the communications circuit section on page 53 H 1. Power supply. Power supply failure connected to IOR6. The system cables screen can be earthed at the power supply. Also remember that metal parts in doors or vehicle barriers can be in contact with earth.

For readers installed on these surfaces, the screen must not be connected to the metalwork. Dimension the power supply equipment and cables so that the voltage at the last door is not below the tolerance of the lock and reader.

One way of reducing unnecessary voltage drop is to place the power supply equipment somewhere in the middle of the circuit. Thus, the load will be equal on each side of the power supply. If the distances or the load are too great, multiple power supply units are required. See example below. Avoid placing the cables close to heavy current installations, e.

Remember that a voltage drop between the highest and lowest potential larger than 5V between units may influence the quality of the RS communication. Software installation and configuring is explained in the User Manual. The software consists of three main parts: Installer Normally the first program you use, to configure different type of functions related to physical units like door monitor contacts, alarm zones and connections to PC. Entro This program is used for managing access groups and card holders.

It can be treated as main program because it is used for daily operations. Door and event monitor Used for status information and event logging but can also be used for unlocking doors via the PC. The users wanting to reserve times can use an ordinary web-browser such as Explorer or Netscape and login to the SR34i containing the reservation system.

It requires that the dedicated SR34i have a permanent connection to the Internet when Internet is used. NOTE At least one of the SR34i must be equipped with a Memory card for web reservation see item H, page 31 — which will contain the reservation information. Afterwards the CF8 is mounted in the SR34i intended for reservations. Depending on how the reservation function is specified, one or more InfoPoint IP, IP or touch-screen terminals can be connected to the system through the network.

I e a combination of PC and these terminals is possible. Technically the entire reservation information is stored in an integrated website in a SR34i with its own IP-address on a network. Remove the power from the actual SR34i. Install the CF8 card. Reconnect the power to the SR34i. B Supplied cable with RJ45 type connector and free end. Length is 3 meters. You can mount it on the wall using the supplied fixing parts — or flush mount it in a separate box.

In the terminal there are some keys to navigate on the screen as well as a card reader to identify the user.

The installation manual supplied with the InfoPoint describes the steps to mount and set-up the terminal. High Voltage The InfoPoint housing does not normally need to be opened for proper operation.

However — if needed be aware that the InfoPoint includes high voltage components. This means that you initially install software components for both systems in the same PC. When you then configure functions like filtered and timed triggering to start recording in the Entro, these are then sent to the DVR.

When the conditions for a certain action then are met the DVR starts recording images. You may then replay these directly from the Entro Door monitor with some optional command options. The numbering of cameras will also be needed to bring into the Entro. Some parameters must also be configured in the DVR to get communication work in Entro.

See Appendix 1 — DVR models and settings for different models. Sometimes more doors are needed sometimes also requiring more SR34i controllers — or more PCs are needed. In addition software updates and upgrades may apply. Naturally, an expansion needs at least one working PC connection to handle the necessary setup.

If local area network is used, be sure to reset to the factory crypto key before any expansion is done. All units will start to communicate immediately. Door controllers and readers are installed as before. NOTE The easiest methods when expanding the system is to temporarily reset to the factory installed Default crypto key — and then change it later on when the system installation is finished.

All controllers must be of type SR34i. However, if RS is used instead for PC-communication, the controller can be reached. Regardless of which above, the new PC must fulfill certain requirements: z A separate Bewator Entro software license must be available for this PC. We assume below that the system is reset to the factory installed Default crypto key before any new units are connected to the system and that no preparations for more connections are done.

Start the Installer program on the existing working PC. Click OK — and a new tab appears in the main window in the Installer. The default, earlier hidden connection is now displayed as 1. Change the name of it before going further. Click the tab Connections and start the wizard by clicking New. This is noted on the CD case for the new software license. You have now created a new connection for Entro and can exit the program in the existing PC.

Start the new PC and install the Bewator Entro software according to instructions in the User manual. A separate software license is needed. Start the Installer and select at login that a new connection shall be created. Follow the instructions on the screen similar to above. You have now defined in which way the computer will communicate, entered the system name etc.

Exit and start Bewator Entro and Change Crypto key. Sometimes it is easiest to use the RS port. Remember that the SR34i have built-in menu commands for checking editing different parameters.

It is important that the set-up is correct. This means: z Correct System name. If an SR34i is found you can add it and configure it like the other controllers. If the conditions for the above are not met - proceed as follows: Be sure the PC has an updated database. Change to Standard crypto key temporarily for the whole system.

Select the address on the new SR34i — and power it up. Set up the networking parameters e g IP address using the keypad and display. Eventually you must erase the memory of the SR34i. The database and the crypto key are sent from the PC - to the controller. Change name and set-up the parameters for this controller. Start Bewator Entro and Change Crypto key. Installing more readers It is very easy to install more readers in the system. You only need the necessary cabling and ensure the following: z The DC12 or DC22 are available for the reader.

In the Installer program there are improved functions for controlling the mechanism for patching the segment controllers. The status of the different units is displayed. In a system you are now able to use the same PC for updating all controllers at the same time. Also there is better information about the status of each updating process. You can actually see the estimated time. This applies for all controllers — not only the one connected to the PC.

Proceed like this for the actions you want to do: 1. All controllers are listed on the screen showing the status for the different units address, product, version, voltage level. If any controller fails to communicate there is a cross over the unit.

Click on Update firmware — and select which version to download stored in the Entro program folder. It is possible to download an old version.

Click on Next and mark the SR to be updated. Click on Finish. A progress bar is displayed for each controller showing the remaining time You cancel the process at any time by clicking Cancel update — no update is performed and the old version remains.

This requires that the units are on-line. NOTE During download the door is unlocked if this is defined in the Security level in off-line condition. All other selections results in a locked door. Click on Save as — as an image in JPG format is stored on disk. PCs communicating with one system directly and with another via modem must have one COM port for connection of a segment controller and another for connection of a modem.

Below is an example of a configuration where a PC has direct contact with one Bewator Entro system and modem contact with another. System 1 2. System 2 63 Bewator AB If you have installed a modem TD35 at the remote site and its telephone number is available there is no need to do the configuring on site. You can connect the SR34i to the modem, hook on the line but do the configuring at the host computer instead even if this may take longer time.

XH X However — if you still want to configure it on site, you do this through the RS link and then switch to modem when it is done. Proceed according to the chapter Configuring the modem based system on site.

XH You should then, temporarily, connect a PC with the Bewator Entro software to one of the segment controllers to be able to configure the system see the next chapter. When the configuring is finished you can disconnect the PC and connect the modem instead. Do not forget to test the communications circuit and the power supply according to the instructions on page For the system to work you should also program information about doors and segment controllers.

Configuring the new system should be done on location, i. Start Installer and click the tab New connection and you start a wizard to establish the connection between the PC and the controller. No login is needed because the system database is probably new and will use the default user name bewa and password pass. Select New system and proceed. Select RS and proceed. The software automatically detects the correct COM-port. Enter a name for the new system in the Site name field, e. Oak lane.

This name will be displayed in the Bewator Entro Login windows, for the user to choose whichever system he or she wants to work with. This name must be unique and identical with the name you will be asked to enter when setting up the main computer see page XH X It is very important that you make note of the system name.

If the PC has to be replaced you must enter the same system name once again. Exit the wizard by clicking Finish. Now the Installers main window is displayed. You perform the set up of doors etc when you are on site according to the instructions given in the User manual.

Instead of later on via the modem connection. Now the main configuring is done and you now prepare to connect the modem. In Installer click on the Connection tab. Mark the tick box Modem and a new tab is displayed.

Enter the modem telephone number. The string can be modified if needed. If the modem needs to be able to call the PC, enter the desired telephone number in the Telephone number to PC field. If the modem needs to be able to call the PC, you enter the name of the System user who shall dial up the PC so that the PC know where to store the events. Set also for which circumstances. The following alternatives exist: — After desired number events.

Means that the segment controller calls the PC following the desired number of events. Means that the segment controller calls the PC following each alarm event. Means that the segment controller calls the PC fol- lowing each modification in the database. A call is made every 15 minutes if the database is modified. NOTE 1 Activation and deactivation of alarms as well as PIN code alterations are a database modification, which means that calls will be made every time this occurs.

Click OK. Now you have configured all the information about the new system. Disconnect the PC you have used for configuring the system and connect the modem instead see next page. When the modem is installed the installation is completed. The only thing remaining is to transfer the information configured for the new system to the central PC used to configure both systems. Watchdog resets the modem automatically in case of an interrupted connection or power failure.

Then you will need to create an initial connection in the PC to the modem to be able to transfer the information. Start Bewator Entro Installer Note that if the PC has no system installed, the wizard starts automatically and you start the wizard directly without login.

Go to tab New connection and start the wizard. Select Existing system and proceed. Mark the modem choice and enter the telephone number of the modem. Now the connection is set up and you might proceed dialing up the remote site as below - or later you can log in and dial up.

Enter the Site name and System name. NOTE It is very important that you enter the same system name as when you installed the modem. The wizard will now try to connect dial-up the remote site.

If this fails — proceed as below. The Bewator Entro Installer main window is displayed. Click the lifted handset symbol on the tool bar or choose Call on the Modem menu. A message is displayed while the system tries to establish a connection. When the connection is established the systems are in direct contact, i. The new system is now ready to receive information about time schedules, persons, access groups and doors according to the User manual. This way information transfer will be quicker and safer.

This is quite natural because it is also a security system to be used for controlling e g access to doors in different kind of facilities. Remember, this not a program just guidelines to the programming interface.

With BAPSI this is done in a specified and safe encrypted way that still keeps the access control system on a secure and integral level. The specification can be requested from Bewator. Normally the User interface in access control software allows for functions like card registering, time schedule configuring and standard event logging and searching. In this case the supplier of the external reservation software made a modification to their software module, which writes data into a file — and Bewator developed a special module that reads this file and forwards this information to the access control system 69 Bewator AB This is described in the documentation supplied with the BAPSER but you can invoke the menus by proceeding as follows: 1.

Start the Installer program and click on Connections. Click on New. Enter the necessary parameters applying to the actual application. It will also make sure the implementation will run smoothly. If you have questions, do not hesitate to contact technical support. Note - when Internet connection is used, the following ports have to be open in fire-walls or similar and configured as follows: z if communication is used between PC and the chosen SR34i.

Segment controller for 4, 8, 16 or 32 doors z Four built-in communication interfaces: — RS — for connection of PC, printer or modem. DC12 Door controller z Door controller for 1 door and connection of up to two Entro readers. IOR6 Relay central z Relay central for — Lift control — Reservation function or — Timer control — Common alarm — Emergency opening — Power failure warning z 6 voltage free relay outputs.

Normally you probably install the whole MX software suite to be able to both control the detailed settings of the MX DVR - as well as viewing. It is however possible to only install the RemoteView module to view recordings from Entro.

We recommend that the MX software is installed on the C-drive. When the parameters are configured — enter them into the Entro Installer program when creating connections and cameras. Read more how to do in the Entro User Manual. Otherwise no view will be displayed 76 Bewator AB You have to activate that at the MX itself.

It's not possible with the remote configuration. If the distances or the load are too great, multiple power supply units will be required. Local reader power supply Whenever one or several readers are connected to a local power supply, remember to join the negative wires 0 volt to avoid potential differences.

See example below. Lit green when CR1 is powered. Connect to terminal nos 1 and 2 on the BC circuit board. Fit ohm resistor between the A and B of the communications in the CR1 unit at the each end of the line.

Each SR34i is controlling the card readers. A maximum of eight BCs can be connected to each SR34i, but other reader types can be included. The BCs are connected to the system via the CR1 converter.

Card readers in Entro systems Having installed the card readers and connected them to the CR1 converter, addresses should be allocated to each card reader and the communications circuit and power supply should be checked. Check the communications circuit When all units are connected but with all removable terminal blocks disconnected in the CR1s , check on reader block nos.

Check the power supply Connect the power supplies. Allocate addresses to the card readers 1 Open the card reader if it is not already open. The card reader starts beeping. Start programming Start programming according to the instructions in the SiPass Entro manual.

BC Installation and User Manual 25 Programming standalone installation In the sections below are the instructions on how to program the BC if the card reader is operating as a standalone unit. To be able to program the card reader you have to set the card reader to programming mode. This is done by entering a six-digit code see the next page. Correct programming: Confirmed by a rising signal consisting of two quick beeps.

Faulty programming: Confirmed by a falling signal consisting of one long and one short beep. If, having entered programming mode, no key is pressed within 20 seconds, the unit will leave programming mode. The lock is located on the underside of the card reader.

The password is now set. Set the card reader to programming mode To program a function, the card reader has to be in programming mode.

Proceed as follows: 1 Press B. If the wrong password is entered two times in succession, the card reader is blocked from further attempts for 40 seconds. From then on the card reader is blocked for 40 seconds each time two incorrect passwords are entered. The unit automatically goes back to programming mode. Use two digits, e.

Go to step 9. Erase a time zone 1 Set the card reader to programming mode. Example: To include time zones 1, 2 and 4, enter Use 2 digits, e. The red LED flashes as the cards are logged on. The existing code, if any, will be over-written. If a holiday period is being programmed, enter the duration in days of the period, including the starting date.

Max number days Delete individual holidays This function is used to delete individual holidays, as distinct to deleting all programmed holidays see the next section. Set door release time The door release time determines for how long the lock should remain released following a correct transaction.

The default value is 7 seconds. This is how to change the opening time, if required: 1 Set the card reader to programming mode. The buzzer reminds the person entering to close the door immediately as an alarm is about to go off. This is how to change the door held warning time, if required: Set the card reader to programming mode. If you do not want the buzzer to beep on key presses or door opening, it can be turned off.

Note that even when the buzzer is off for normal operation, it will continue to sound during programming. Proceed as follows: 1 Set the card reader to programming mode.

The calculation factor is added to the last four digits in the card number. Example: If the card number is and the calculation factor is , the code will be If you want to use your own cards and they should be read differently, enter from which position on the magnetic strip the reader should start reading and how many digits should be read max.

Previously logged on cards will not work if you change the card parameters. Press A To reset this function to the default setting, press A at this point. Enter the number of digits to be read If less than 8 digits are used in the card number, add as many 0 digits as necessary to make up an eight-digit card number when using the A03, A04 and A16 commands.

Example: If the card number is , enter when using the A03, A04 and A16 commands. Proximity reader When using proximity readers the co-operation between the reader and the cards are stated at the factory and cannot be changed.

The digits used for logging on a card — or cancelling a card — will be the eight digits seen on the card. E g A warning tone is heard. The warning tone sounds until all six digits have been entered.

If you should forget the password you can set a new password. Read the Set password. All previously data have now been erased. Printout of programmed common codes Using this function, printouts of programmed common codes can be requested. RT 07 S Release time 07 sec. Printout of programmed holidays 1 Set the card reader to programming mode. Common code CO Access granted. Card CP Access granted. Illegal common code NL Access denied.

Card not logged on IP Access denied. Should the wrong PIN-code be entered 3 times in succession the card is automatically cancelled and must be logged on once again. The toggle function If the toggle function is activated, the user can open the door in one of the above-mentioned ways depending on the current security level. The door remains open until a user need not be the same one as opened the door again completes a valid transaction or until another security level starts.

Otherwise enter the existing code. You have now set the PIN for your card. Example 1: If the PIN code is , press instead. Example 2: If the PIN code is , press instead. When a duress code is entered, the door is opened at the same time as the alarm output is activated an alarm is sent to a security guard or similar. The alarm output will be activated until it is reset by entering programming mode. Adjust the button. Memory error. Change card reader. Cannot enter programming mode. Red LED is lit after two trials.

Wrong password. Choose a new password. Green LED is lit on Lock error. Check cable between card reader and lock. Change locks. The jumper between Attach jumper. A card is used at the The reader head is card reader but nothing loose. Magnetic happens. No beep is only heard. The reader head is dirty. Magnetic only Tighten the reader head. Clean the reader head using a special cleaning card. Change card reader or reader head. The reader head is damaged. A card is used at the The card is not Log on the card.

BC 70 mA. Duress output: Alarm output: Tamper switch: Inputs: Open collector to 0 volt. Max mA, 30VDC. Open collector to 0 volt. Max 1A, 30 V DC. Normally pulled high.